基于PolyWorks虚拟装配间隙面差计算分析研究

随着当今社会汽车制造业的迅猛发展,高标准和高需求已经是消费者对汽车制造凯歌的主旋律。而这其中,汽车钣金件的间隙面差就是其中一个重要因素。快速检测间隙面差是否满足设计要求直接关系到汽车白车身的生产精度和企业的工作效率。传统计算间隙面差大多利用量具,易划伤被测物且在零件实际装配后才可测量,降低生产效率,而非接触测量造价昂贵。本课题基于实物的汽车钣金件虚拟装配,对间隙面差的计算方法进行分类与参数调整,提出一种高效率、高标准的间隙面差计算流程。     

Trimetallic NiFeCr-LDH/MoS2composites as novel electrocatalyst for OER

The development of efficient and stable oxygen evolution reaction (OER) catalysts is an ongoing challenge. In order to solve the problem of low oxygen evolution efficiency of the current OER catalysts, a novel material was synthesized by the incorporation of NiFeCr-LDH and MoS₂, and its structural and electrochemical properties were also investigated. The introduction of MoS₂ improves the electrochemical performance of NiFeCr-LDH. The polarization curve shows that the potential of composite material is only 1.50 V at a current density of 10 mA cm^?2, which is far superior to commercial precious metal catalysts. In addition, the stability experiment shows that the composite material has excellent stability, and the current density has little change after 500 cycles. Furthermore, we found that some metal ions, such as Ni, Cr and Mo, exist in the form of high valence on the surface of NiFeCr-LDH@MoS₂, which is also conducive to the occurrence of oxygen evolution reaction.     

Alkali metal ion substitution induced luminescence enhancement of NaLaMgWO6:Eu3+ red phosphor for white light-emitting diodes

Alkali metal ion substitution is an effective strategy to improve the luminescence properties of phosphors. In this work, a series of red-emitting phosphors Na_1-xLi_x/2K_x/2La_0.6Eu_0.4MgWO₆ were prepared by a traditional high-temperature solid-state reaction. Their phase structure, microstructure, luminescence properties and potential application in phosphor-converted white light-emitting diodes (pc-WLEDs) were investigated in detail. X-ray diffraction (XRD) result revealed the formation of a solid solution when x?≤?0.3, which kept monoclinic structure of NaLaMgWO₆. Photoluminescence investigation indicated that the partial substitution of Li⁺/K⁺ ions for Na⁺ ions improved largely the red emission of Eu³⁺. Based on the optimized Na_0.7Li_0.15K_0.15La_0.6Eu_0.4MgWO₆ sample with relatively good thermal stability, a WLED device was fabricated by combining a near-ultraviolet (NUV) chip (~400?nm) with the phosphor mixture of commercial green/blue phosphors and the optimized red phosphor. The results indicated that the optimized red phosphor in this work could be a potential candidate for WLEDs pumped by NUV chips.     

Synthesis of highly active and stable Pd/C catalysts toward HCOOH dehydrogenation by a simple NH3 adsorption method

Pd catalysts supported on activated carbon (Pd/C–NH₃) toward HCOOH dehydrogenation were prepared by a simple adsorption method using ammonia (NH₃) and Ar as the working gas. The results show that the TOF_initial of Pd/C–NH₃ was 459.8 h⁻¹ at 50 °C. When the reaction was carried out for 4 h, the HCOOH dehydrogenation ratio over Pd/C–NH₃ was about 81.2%, which was 1.15 and 1.13 times, respectively, as that of the as-prepared Pd/C catalyst without any treatment (Pd/C–As) and the Pd/C catalyst purchased from Sigma-Aldrich (Pd/C-CM). The total amount of H₂ and CO₂ produced by using Pd/C–NH₃ to decompose HCOOH in the third cycle was 99.4% of the gas produced by the first reaction cycle, and 1.80 and 12.60 times, respectively, as that of Pd/C–As and Pd/C-CM. The characterization results indicated that the Pd active species in Pd/C–NH₃ migrated to the outer surface of the carbon support during the reaction, and the pore volume of the carbon support became larger, which were beneficial to the reaction. These factors made Pd/C–NH₃ exhibit excellent HCOOH dehydrogenation activity and stability. NH₃ adsorption is a simple and effective method for preparing high-performance Pd/C HCOOH dehydrogenation catalysts, and has important guiding significance for the preparation of other carbon supported noble metal catalysts.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Promoted electrocatalytic hydrogen evolution performance by constructing Ni12P5–Ni2P heterointerfaces

Transition metal phosphides (TMPs) have been considered as cheap alternatives of precious metal platinum for electrochemical hydrogen evolution reaction (HER). In the past decades, many reports have indicated that the engineering of heterointerfaces between different components could efficiently enhance the activity of HER catalysts. Here, we report a facile method to construct Ni₁₂P₅–Ni₂P heterostructure by using a low temperature phosphorization strategy. The obtained Ni₁₂P₅–Ni₂P heterostructure shows high activity toward HER with an overpotential value of 166 mV at 10 mA cm^?2 and a Tafel slope of 60 mV dec^?1 in 0.5 M H₂SO₄. Compared with pure Ni₂P and Ni₁₂P₅, the Ni₁₂P₅–Ni₂P heterostructure has more active sites and faster HER kinetics due to the presence of the interfaces between Ni₁₂P₅ and Ni₂P. Furthermore, we used the obtained Ni₁₂P₅–Ni₂P as cathodic catalyst and IrO₂/Ti as anodic material to set up a proton exchange membrane (PEM) electrolyzer which shows good stability after 120 h continuous constant current electrolysis at 200 mA cm^?2. This work demonstrates the positive effect of heterostructure for HER catalysts and provides a feasible strategy for constructing earth-abundant electrocatalysts.     

腔磁力系统中的诱导透明和快慢光传播

为了在腔磁力系统中实现可控的磁子诱导透明、磁力诱导透明以及快慢光传播,建立了一个混合腔磁力系统.该系统由一个含有YIG球的微波腔和在z方向对球施加一个均匀的偏置磁场组成,并用强泵浦场驱动磁子和弱探测场驱动微波腔.研究表明,通过调节腔与磁子之间的相互作用强度和微波腔与磁子的耗散比,可以增加磁子诱导透明(MIT)、磁力诱导透明(MMIT)的效果和提高快慢光传播的速度.该研究结果可为磁力诱导放大、量子光学操纵和量子信息存储以及灵敏光开关的研究提供参考.     

High ultraviolet transparent conducting electrodes formed using tantalum oxide/Ag multilayer

We investigated the optical and electrical properties of Ta₂O₅/Ag/Ta₂O₅ films as functions of the thicknesses of the Ta₂O₅ and Ag layers. It was found that with an increase in the thicknesses of the Ta₂O₅ and Ag layers from 10 to 40 nm and from 12 to 24 nm, respectively, the sheet resistance, carrier concentration, electron mobility, and resistivity of the Ta₂O₅/Ag/Ta₂O₅ film varied from 2.02 to 8.95 Ω/sq, 5.74 × 10²¹ to 2.92 × 10²² cm^–3, from 13.21 to 24.07 cm²/V·s, and from 8.89 × 10^-6 to 8.24 × 10^-5 Ω cm, respectively. The average transmittance (T_av) of the multilayer samples ranged from 57.18% to 93.99%, and it depended on the Ta₂O₅ and Ag layer thicknesses. The highest T_av of 93.99% was observed for the film with 35 nm thick Ta₂O₅ and 18 nm thick Ag layers, and the peak Haacke's figure of merit (157.04 × 10^–3 Ω^–1) was obtained for 20 nm thick Ta₂O₅ and 21 nm thick Ag layers. Ta₂O₅ (100 nm) and Ta₂O₅/Ag/Ta₂O₅ (20 nm/21 nm/20 nm) samples had optical bandgaps of 4.70 and 4.45 eV, respectively. Film Wizard simulations were conducted to understand the dependence of the transmittance of the multilayer on the thicknesses of the Ta₂O₅ and Ag layers, and phasor analyses were performed to determine how the transmittance of the Ta₂O₅/Ag/Ta₂O₅ (20 nm/21 nm/20 nm) film depended on the Ta₂O₅ layer's thickness.     

Effect of sintering temperature on solidification and migration of non-volatile and volatile heavy metals in glass-ceramic

Using tailings as material to prepare glass-ceramic is an excellent way to achieve the resource utilization of solid waste. However, at present, researches on the solidification and migration of heavy metals are limited. Therefore, in this study, ten groups of samples were prepared by controlling sintering temperatures. The solidification, migration, and leaching behavior of non-volatile and volatile heavy metals were studied. The research showed that, with the increase of temperature, the properties of the samples were improved. Fe participated in the phase transformation and evolved into insoluble iron pyroxenes solid solution, while Pb was homogeneously distributed in the glass matrix of glass-ceramics. The leaching concentrations of Fe and Pb in the glass-ceramics were 0.055 mg/L ～0.087 mg/L and 0.074 mg/L ～0.140 mg/L, which were far below the threshold value. The results showed that heavy metals can be effectively solidified in glass-ceramics and have good environmental benefits.     

Vacancy-engineered V2O5-x films for ultrastable electrochromic applications

In the present study, we prepared vacancy-engineered V₂O_5-x films for electrochromic (EC) applications. To investigate the vacancy effect of V₂O_5-x films with high EC performance capabilities, precursor concentrations of V-based sol solutions were varied at 1 wt%, 5 wt%, and 10 wt%. Among them, V₂O_5-x films with a precursor concentration of 5 wt% (V₂O₅-5wt%) showed superior EC performance outcomes due to the (001)-plane-oriented crystal structure, which provides high electrical conductivity with the oxygen vacancy (V_o). In addition, the gravel-like uniform surface morphology with the optimized film thickness provides a stable electrochemical reaction during the EC measurement. As a result, V₂O₅-5wt% exhibited fast switching speeds (2.1 s for coloration and 3.6 s for bleaching), high transmittance modulation (ΔT) (51.32%), high coloration efficiency (CE) (52.3 cm²/C), and excellent cycle stability (85.85% ΔT retention after 500 cycles). In addition, V₂O₅-5wt% showed energy storage capability of 443.7 F/g at a current density of 2 A/g, thus proving its potential for use in multi-functional applications. Therefore, these results provide valuable insight related to the engineering of vacancies in EC films to achieve high-performance EC devices and additional multi-functional applications.